It is highly recommended that your system is sanitized each year. Just follow these 16 steps*:

  1. Turn off incoming flow to the system.
  2. Open the faucet where the filtered water comes out (to relieve the pressure).
  3. Remove and open the filter housings. Be careful not to spill!
  4. Remove cartridges from housing.
  5. Remove and rinse the O-ring in the filter housings. Return O-ring to housing. FYI: Some manufacturers recommend replacing O-rings each year.
  6. Inspect cartridge for sediment buildup. If high sediment buildup is present it may be time to replace the cartridge.
  7. Clean filter housings with warm soapy water and a brush. Also, clean inside the filter housing cap.
  8. Prepare sanitizing solution in a clean bucket as follows: 1/3 teaspoon of unscented household bleach for 1 gallon of water.
  9. Add 1 cup of the sanitizing solutions to each filter housing. Replace the housing cap (DO NOT replace the cartridge)
  10. Replace housing into the system and run the system, letting the housing and system to fill with water.
  11. When water starts to flow out of the faucet, close the faucet.
  12. Allow water to flow through the housing and system for 30 minutes.
  13. After 30 minutes shut-off incoming flow, remove housing(s), and discard sanitizing solution.
  14. FYI: Place the carbon block cartridge (with netting) in the first housing, and the KDF/GAS cartridge (with plastic casing) in the second.
  15. Replace the housings with cartridges back intot he system, open the valve and allow water to flush the system for five minutes.
  16. Close the faucet and check the rates.

*See these steps in action below:

Read More →

The #1 Rule of Compressed Air:

 

For every 20 degrees that compressed air is cooled, the air loses 50% of its ability to hold moisture in vapor form (humidity) and it is dropped out as a liquid.

The Difference between Air Drying and Air Filtration:

  • Air Drying is he removal of water vapor (humidity) from compressed air.
    • This is typically accomplished in one of four ways:
    • Desiccant (molecular sieve, activated alumina, silica gel)
    • Membrane
    • Refrigeration
    • Deliquescent
  • When to use compressed air dryers:
    • Air dryers should be used when you want to remove or reduce the humidity levels in your compressed air system to meet or exceed the air quality requirements for their compressed air demands.
  •  Air Filtration is the removal of particulates, water, oil droplets, and oil aerosols.
    • This is most effective when done in stages:
    • Water separator – removes bulk water, oil, and large particulates (down to 10 micron)
    • Coalescing filter – removes oil, small aerosols and fine particulates (down to .01 micron)
    • Activated carbon filter – removes oil vapors; eliminates odors and taste (down to .003ppm)
  • Where to place compressed air filtration:
    • The further away from the compressor, the more effective your filtration will work.
    • On or near the equipment, directly connected to air supply connection (IMPORTANT)
    • In front of all air dryers as pre-filters
    • Water separators should be placed at all air tool drops with regulators

 Important Things to Know:

  • Proper control of air pressure throughout your facility can help save 10-15% of your compressed air energy costs.
  • Repairing an audible air leak can save you $50 or more per year in energy used to drive your compressor.
  • When sizing a compressor for manufacturing, it is important to calculate total machine air consumption as well as total air consumed by machine operators and other personnel.
  • Proper control of air volume (CFM) will make all your air drying and filtration technology perform at their rated capacity. Most pieces of equipment have a manufacturer’s specification of volume consumption along with the recommended operating pressure.
  • Improper use of volume can cause an “over-flowing” of the rated capacity of your dryer or filtration which causes a carry over of moisture and contaminants.

Learn more ways you can save money and eliminate costly down time with the Compressed Air 101 video below!

Tsunami Compressed Air Solutions™ offers a complete line of products engineered to give customers dry, clean air for their specific application demands. These systems use the latest technology to provide the highest quality compressed air available. Watch this video to learn some of the key reasons you need to maintain dry, clean air in your system.
 
Read More →

An estimated 1.8 billion people lack access to safe drinking water. Kohler Co., a global leader in the plumbing industry, has developed a ceramic filtration system called KOHLER Clarity and will work with World Vision, iDE and Water Mission, among others, to enable people in remote regions to access safe, reliable drinking water. The system was designed to bring aspirational products to an affordable price point so NGOs and end users do not have to choose form over function.

Read More →

 

Did know you …

The Earth contains 366,000,000,000,000,000,000 gallons of water.
That’s 366 quintillion gallons of water.
Only .007% is potable.
Today 7 billion of us share this precious resource.
The ice on Kilimanjaro has shrunk 85% in 100 years.
The Aral Sea — once Asia’s second-largest lake — is one tenth the size it was 50 years ago.
Groundwater depletion in Mexico City has made it sink 30 feet.
2 million residents now lack piped water.

Watch the video to learn more!

Read More →